PML-600 Magnetic Lifter - 600 kg Capacity
KDV: Fiyatlara %20 KDV dahildir
Minimum Sipariş: 1 Adet ve Üzeri Sepete Ekle
| Stock | : | In Stock |
| Model | : | MGK-PML-600 |
| Category | : | Manyetik Kaldıraçlar |
PML-600 Magnetic Lifter 600 KG - LIFTS 600 kg ON MATERIALS AT LEAST 30 mm THICK.
The manual magnetic lifter with a lever used for lifting metal sheets carries heavy metal materials by being attached to magnet cranes or similar devices. It is referred to as PML-600 magnetic lifter in some sources. The PML 600 magnetic lifter, which is highly effective in areas where human strength is insufficient, has a carrying capacity of 600 kg.
How to use a magnetic lifter?
Offering 600 kg of power, the PML600 magnetic lifter does not require extra power. The lever lifter system, which does not require electricity, provides permanent power. The magnetic power is activated with the help of the lever on it. If the lever is not pulled, the device does not provide any power and is in the off position.
- Clean the surface of the part you will pull before using the device.
- Bring the magnetic lifter to the center of gravity of your part.
- To activate the device, first lower the magnetic lifter onto the part to be lifted.
- Pull the lever and activate the device.
- After the magnetic power holds your part, lift and carry the metal with the help of a crane or similar.
- When your part reaches the desired position, bring the lever back to the closed position.
!!! IF THE MATERIAL TO BE CARRIED IS THIN LIKE 1 - 2mm, PLEASE CONTACT THE TECHNICAL TEAM!
SINCE THE CARRYING CAPACITY WILL DROP ON THIN MATERIALS, A HIGH-CAPACITY LIFTER SHOULD NOT BE PREFERRED.
Power efficiency of magnetic lifters according to material thickness?
Our magnetic lever lifters offer power according to the thickness of the metal it will pull against. You can check below how much power the PML model you will buy offers at which material thickness.
Power efficiency of magnetic lifters according to material quality?
Magnetic lifters offer different power values according to the quality and type of metal they will pull. It provides full efficiency when pulling low carbon steel, while it gives the lowest pulling power in cast iron.
| Material | Efficiency |
| Low carbon steel | 100% |
| Medium carbon steel | 90% |
| High carbon steel | 80% |
| High alloy steel | 70% |
| Cast iron | 50% |
| Stock No | Power (Flat) | Power (Oval) | Max. Power | Weight (kg) | W | L | H | I | °C |
| MGK-PML-100 | 100 | 50 | 350 | 3 | 62 | 92 | 67 | 126 | <80 |
| MGK-PML-300 | 300 | 150 | 1050 | 6 | 92 | 162 | 91 | 155 | <80 |
| MGK-PML-600 | 600 | 300 | 2100 | 20 | 122 | 232 | 117 | 196 | <80 |
| MGK-PML-1000 | 1000 | 500 | 3500 | 37 | 176 | 258 | 163 | 285 | <80 |
| MGK-PML-2000 | 2000 | 1000 | 7000 | 68,3 | 234 | 378 | 212 | 426 | <80 |
| MGK-PML-3000 | 3000 | 1500 | 10500 | 87,5 | 286 | 458 | 261 | 521 | <80 |
| MGK-PML-5000 | 5000 | 1800 | 18000 | 198 | 296 | 720 | 266 | 700 | <80 |
